Trimming out an accordion door is generally the same process as trimming out most other interior doors. Since accordion doors tend to be utilitarian, you should keep it simple, choosing flat, plain trim. Measure the width of the top of the doorway from the inside of each upper corner.

How do you reduce the width of a concertina door?

Cut a piece of 2-by-2-by-96-inch fir to fit inside the door if you've cut more than 2 inches off the door and exposed the hollow core. Use the table saw to cut it to width and length. Place glue on both sides and tap it into the side of the door until it's flush with the side.

Can you cut down a folding door?

The width of a bifold door can be cut up to ¼ inch on each side to fit better into a door rough opening. Tape off the side to be cut with painter's tape then use a circular saw or planer to trim the width of the bifold door. Lightly sand the edges to remove burrs and paint the sides to reseal the door.

Can you shorten concertina doors?

The versatility of an accordion door gives homeowners the option to install a self-contained door that does not disrupt the floor space on either side of the door. ... One plus of an accordion door is the option to trim the bottom to fit any size door opening.

Can you cut a vinyl door?

You can trim your door up to 3/8” from each side and top and 1” off the bottom. If you trim more than these amounts you will compromise the integrity of the door an void the warranty. A standard circular saw will do the job — vinyl cuts just like wood.

Folding Doors - how to install DIY tutorial

17 related questions found

Can you trim vinyl accordion doors?

Trimming out an accordion door is generally the same process as trimming out most other interior doors. Since accordion doors tend to be utilitarian, you should keep it simple, choosing flat, plain trim. Measure the width of the top of the doorway from the inside of each upper corner.

Can you cut a bifold door to fit height?

If you ordered a bifold door and find it's a bit too long for the door's height, it's a simple matter to trim the door to fit. Installing carpet with a thicker nap can sometimes cause the bifold door to drag. As a house settles over time, you might also find you need to adjust the height of a bifold door.

How much smaller should a bifold door be than the opening?

The actual dimension of bifold doors is always ½'' smaller in width than the stated size to accommodate the necessary clearance for proper operation of doors. Bifold doors must be 1-1/2'' shorter in height than the finished opening.

Can you cut Jeld Wen bifold doors?

Any trimming of your Bi-fold doors will invalidate the warranty. Bi-fold interior doors must be purchased in the correct size for your opening so that trimming is not necessary. If you need help with installation, view our handy fitting video here.

Can you cut sliding closet doors?

It is possible to shorten bypass doors. You have to remove the bottom of the frame, splay the side frames wide enough to cut the panel, cut the side frames to length, reinstall the bottom frame.

How much can you cut off the bottom of a hollow core bifold door?

Remember, you only have about an inch and a half available to lose from the average hollow core door. If you need to take off more than that, think about replacing the door instead. Start by drawing a pencil line to show where you're cutting, then grab a knife and a guide and score the surface of the door.

How do you cut the width of a door?

To trim the width, take evenly from both sides. To cut the door with a circular saw, place painter's tape along the cut line. Mark the line on the tape and score it with a utility knife to prevent chipping. With the saw braced against a cutting guide and its blade on the waste side of the line, trim the door.

How do you size a bifold door opening?

Measure the width of the opening at the top, bottom and middle. Measure the height on both sides and in the middle. Take the smallest measurements and deduct half an inch (the fitting tolerance) to get the size of the door you need to order.

How much should be the gap between bifold doors?

The goal is to adjust the doors to leave an even 1/8-in. vertical gap between them (Photos 1 and 2) and an even horizontal space along the top—without allowing them to scrape on the door jambs or floor. You can't always get the doors perfectly aligned on all four sides, especially if the opening is out of square.

Are accordion doors adjustable?

It's important to understand how these doors work and what is — and is not — adjustable. ... The top pivot pin controls the pitch of the doors — the way they slant toward or away from the frame. On a pair of bifold doors, the top pins also control the gap between the doors.

Can I cut a plastic door?

To make straight cuts on thicker sheets of acrylic and polycarbonate plastic (greater than ⅛ inch thick), you'll need to use a table saw or circular saw. ... Secure the plastic safely to the work surface with a clamp. Use the circular saw (or table saw) to cut through the plastic in the same way you'd cut through wood.